Revistas
Revista:
CIC CENTRO INFORMATIVO DE LA CONSTRUCTION
ISSN 1576-1118
Vol. 575
Año 2022
Págs.62 - 64
Autores:
Araya, R. (Autor de correspondencia); Guillaumet, A.; do Valle, A.; et al.
Revista:
SUSTAINABILITY
ISSN 2071-1050
Vol. 14
N° 3
Año 2022
This article presents the latest developments of the Spanish- and Portuguese-speaking countries of Europe and Latin America towards the development of sustainable timber construction. As most regions related to these countries have not traditionally employed timber as primary construction material, bringing the development of sustainable timber construction into fruition requires a wide range of actions, such as the elaboration of new educational programs, construction of demonstrative buildings, dissemination activities, settlement of public policies, elaboration of new construction codes, and the creation of new certification bodies. This article presents an overview of the state of the development of the different countries of Ibero-America, showing a very uneven development in the region. In addition to national analyses, a perception survey of 233 professionals from different countries was conducted, allowing for the identification of good practices, present gaps, and opportunities, as well as barriers for developing sustainable timber construction. It is concluded that in order to promote the development of the timber construction industry in the region, it is necessary to progress on regulatory, cultural, and material availability issues, where international experience, demonstrative buildings, and the implementation of public policies are crucial.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 235
Año 2021
Págs.112062
Finite element models tend to overestimate the actual elastic response of structural timber connections. The paper shows how such overprediction relates to the modelling of the contact between fasteners and timber. The use of a control parameter called stiffness contact is proposed. After an experimental campaign, a method to determine it, based only on the geometry of a rectangular contact area, is proposed. The modeling adequacy is demonstrated by applying it to dowel embedment and moment resistant wood joint tests. The obtained results show good agreement with the experimental test series.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 241
Año 2021
Págs.112450
Timber connections with steel dowel-type fasteners may fail in ductile or brittle ways. The design of this joints was traditionally focused on ductile failure, assuming that brittle failure could be avoided by means of geometrical limitations. However, recent studies demonstrated that these assumptions do not always guarantee ductile failure. A new design model for timber connections with small diameter dowel-type fasteners is provided in this paper. Its improved accuracy is demonstrated by analysing an extensive database of experimental tests and comparing its prediction accuracy to that of existing models.
Revista:
MAS MADERA
ISSN 2695-4583
N° 15
Año 2021
Págs.40 - 46
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 238
Año 2021
Págs.111766
Timber connections with small diameter fasteners that do not go through the whole timber member (such as screws or nails). may fail in brittle or ductile ways. In order to better understand their behaviour, an experimental campaign of tests of connections with small diameter fasteners loaded parallel-to-grain has been performed. The results and analysis of this work provide further information on the role of different parameters in the brittle failure. Existing models are benchmarked against these tests.
Revista:
MAS MADERA
ISSN 2695-4583
N° 15
Año 2021
Págs.20 - 23
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 247
Año 2021
Págs.113122
The development of accurate structural modelling techniques is required to promote the use of timber as a renewable alternative to other structural materials. Due to their remarkable influence on the global behaviour of a timber structure, an accurate description of the performance of structural connections is needed. Particularly in the case of moment transmitting beam-to-column connections with dowel-type fasteners, such properties are difficult to obtain experimentally. This paper develops a finite element (FE) model that simulates the behaviour of these connections under quasi-static loading, with a focus on the estimation of rotational stiffness and load distribution among the dowels. The model is validated against short-term laboratory tests. Resulting friction between timber members due to the installation procedure must be considered, as it greatly influences the rotational response. Besides, non-linear behaviour of timber and a softened contact parameter have been implemented, and their influence on the FE model validation process is demonstrated.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 242
Año 2021
Págs.112496
Timber connections can fail in a ductile or in a brittle way. A structural design that guarantees a ductile behaviour in case of failure is desirable, especially when facing extreme situations such as earthquakes. This work discusses how the European Yield Model (based on a ductile failure mechanism), included in many standards, combined with a reduction of the effective number of fasteners may provide too conservative results, which may inadvertently lead to risky situations in which a connection assumed to fail under a ductile mechanism would actually fail in a brittle manner. Within this paper, a proposal to improve the discrimination ability to correctly predict the failure mode is proposed.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 209
Año 2020
Págs.109959
The consideration of brittle failure of timber connections requires an adequate evaluation of the capacity of the involved failure planes. Their correct geometrical definition is therefore of utmost importance to obtain an accurate assessment of their capacity. This article presents a new approach to account for the effective thickness of the lateral planes of timber members in connections with large diameter fasteners loaded parallel-to-grain when the fasteners remain in its elastic range, which allows to consider the uneven load distribution along the fastener in a simple way. The proposal is based on a fitting of a beam on elastic foundation model and only requires the slenderness of the fastener as a parameter. It provides a both simple and accurate way to calculate the effective thickness of timber elements.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 217
Año 2020
Timber connections may collapse in a brittle or in a ductile mode. The calculation models of timber joints are mainly focused on ductile failure mode, since it has been traditionally assumed that brittle failure was avoided by respecting a minimum spacing between fasteners. However, this assumption alone does not guarantee a ductile failure. This paper proposes a new design model dealing with brittle failure modes of timber connections with large diameter fasteners (those protruding the whole thickness of the timber member such as dowels or bolts). A comparison between the proposal and the existing models, using an extensive database of tests, is used to demonstrate the improved accuracy of the proposed design method.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 223
Año 2020
Revista:
MAS MADERA
ISSN 2695-4583
N° 14
Año 2020
Págs.34 - 40
Revista:
WOOD MATERIAL SCIENCE AND ENGINEERING
ISSN 1748-0272
Vol. 14
N° 5
Año 2019
Págs.298 - 311
Revista:
MAS MADERA
ISSN 2695-4583
Vol. 13
Año 2019
Págs.34 - 40
Revista:
CONSTRUCTION AND BUILDING MATERIALS
ISSN 0950-0618
Vol. 216
Año 2019
Págs.296 - 313
Revista:
AITIM BOLETIN DE INFORMACION TECNICA
ISSN 0044-9261
N° 318
Año 2019
Págs.4 - 9
Revista:
NEW ZEALAND JOURNAL OF TIMBER DESIGN
ISSN 1171-8323
Vol. 27
N° 3
Año 2019
Págs.17 - 26
Revista:
NEW ZEALAND JOURNAL OF TIMBER DESIGN
ISSN 1171-8323
Vol. 27
N° 3
Año 2019
Págs.17 - 26
Revista:
MAS MADERA
ISSN 2695-4583
Vol. 12
Año 2018
Págs.32 - 37
Revista:
CONSTRUCTION AND BUILDING MATERIALS
ISSN 0950-0618
Vol. 173
Año 2018
Págs.238 - 250
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 171
Año 2018
Págs.895 - 910
For safety reasons, ductile failure in timber connections with dowel-type fasteners is always recommended. It has usually been assumed that it can be achieved by fulfilling minimum spacing requirements between fasteners. However, recent works address the need to account for brittle failure modes (namely splitting, row-shear, and block and plug-shear) in connections loaded parallel-to-the-grain in an explicit manner, in order to evaluate them and achieve the desired ductility. This article describes the brittle failure modes and reviews the existing calculation models proposed by several authors ¿ some of them included in standards. Finally, the performance of these models is assessed against an extensive database of tests gathered from the literature following a comprehensive methodology.
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 170
Año 2018
Págs.135 - 145
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 41
Año 2017
Págs.22 - 24
Revista:
MATERIALES COMPUESTOS
ISSN 2531-0739
Vol. 1
N° 1
Año 2017
Págs.105 - 109
Revista:
MAS MADERA
ISSN 0213-3741
N° 11
Año 2017
Págs.36 - 41
Revista:
MAS MADERA
ISSN 0213-3741
N° 10
Año 2016
Págs.28 - 33
Revista:
ENGINEERING STRUCTURES
ISSN 0141-0296
Vol. 117
Año 2016
Págs.332 - 343
Wood, as a natural heterogeneous material, is a challenging material to simulate. This work presents an algorithm to model both its elastic and post-elastic responses. It allows to model different compression and tension elastic and failure behaviors in both material directions, parallel and perpendicular to the grain. It employs two different strategies: a sequential application of different failure criteria, and the modeling of post-elastic response by means of damage and stress reduction parameters. The proposed algorithm is applied to spruce in two experimental cases with different loadings and failure modes. When reasonable mesh density and increment size are used, the obtained results are in good agreement with the experimental results. The proposed algorithm has been programmed in the commercial software ABAQUS. However, it may be easily applied to different platforms or wood species.
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 38
Año 2016
Págs.36 - 38
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 39
Año 2016
Págs.30 - 32
Revista:
APPLIED MATHEMATICAL MODELLING
ISSN 0307-904X
Vol. 39
N° 17
Año 2015
Págs.5265 - 5277
Several methods for determining in-plane shear properties of anisotropic materials (i.e. fibre reinforced composite materials and natural wood) based on flexural loading have been proposed. One of those methods is the off-axis flexural test that considers unidirectional composite materials subject to three-point bending loading. As a result of the anisotropic behaviour, unidirectional off-axis laminates subjected to flexure present a bending¿twisting coupling that may cause, in the case of 3-point bending loading, a lift-off of the specimen on the fixture supports. Such specimen lift-off has been considered one of the critical features to be considered on the mentioned experimental method. Besides geometrical parameters, material elastic constants, as longitudinal, transversal and shear elastic moduli, influence the validity to use this method for characterising in-plane shear properties. On that sense, an analytical approach for studying the material conditions for which the application of the off-axis 3P-B test is adequate is presented.
Revista:
MECHANICS OF MATERIALS
ISSN 0167-6636
Vol. 83
Año 2015
Págs.103 - 109
Recent biaxial experiments on clear-spruce wood allow to have a more complete understanding of fracture behavior of wood. An elliptic failure surface, like that of Tsai¿Wu, has been previously proposed as a failure surface. Previous works in this area have shown the need for further developments. In this study a new failure model that accounts for existing different couplings and interactions in the longitudinal compressive and tensional domains is presented. The model is based on the fracture behavior of clear spruce wood and related experimental works. The model is more accurate compared to existing phenomenological models.
Revista:
MAS MADERA
ISSN 0213-3741
Vol. 9
Año 2015
Págs.30 - 33
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 35
Año 2014
Págs.30 - 32
¿Y si comprar su casa fuera como comprar un coche? Elegir un modelo base. los equipamientos adiconales, y recibirlo en el tiempo pactado porel precio acordado. El sueño de construir edificios como si fueran elementos industriales, aprovechando todas las ventajas de una producción en serie, puede ser posible, Una empresa navarra, Modula, trata de hacerlo realidad.
Revista:
MAS MADERA
ISSN 0213-3741
N° 8
Año 2014
Págs.30 - 34
Revista:
EUROPEAN JOURNAL OF WOOD AND WOOD PRODUCTS
ISSN 0018-3768
Vol. 72
N° 5
Año 2014
Págs.699 - 702
In this paper, mechanical properties of the four Central American wood species Amapola (Pseudobombax ellipticum), Manchiche (Lonchocarpus castilloi), Pucte (Bucida buceras) and Santamaria (Calophyllum brasiliense) determined in a preliminary experimental study are presented.
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 34
Año 2014
Págs.32 - 34
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 33
Año 2013
Págs.34 - 36
Revista:
MAS MADERA
ISSN 0213-3741
N° 7
Año 2013
Págs.30 - 33
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 32
Año 2013
Págs.32 - 34
Revista:
MAS MADERA
ISSN 0213-3741
Vol. 7
Año 2013
Págs.22 - 29
Revista:
SPEND IN
ISSN 1696-8158
Vol. 59
Año 2013
Págs.106 - 109
Revista:
EUROPEAN JOURNAL OF WOOD AND WOOD PRODUCTS
ISSN 0018-3768
Vol. 70
N° 6
Año 2012
Págs.871 - 882
Many different phenomenological failure criteria have been proposed. These type of criteria do not explain the mechanism of failure itself. They merely identify failure (yes or no) and are usually regarded in practice as a simple and reliable tool for design. Most of them were developed for composite materials, but are extensively applied for wood. In this study, existing phenomenological strength criteria for orthotropic materials were applied to clear wood data. Instead of fitting the criteria to available experimental data, the criteria were used to predict failure of biaxial tests based on uniaxial strength. This procedure is closer to practice, and hence an answer to the question ¿is there any reliable failure criterion for wood?¿ Predictability of the criteria was assessed using normalisation procedure, and statistical significance of the difference of the means analysed. Based on the results, it can be concluded that a general criterion cannot be applied to predict failure, but should be chosen according to the biaxial stress state.
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 31
Año 2012
Págs.34 - 37
Revista:
NAVARRA FORESTAL
ISSN 1579-8771
N° 30
Año 2012
Págs.36 - 38
Revista:
MAS MADERA
ISSN 0213-3741
N° 6
Año 2012
Págs.32 - 37
Revista:
ANALES DE LA MECANICA DE LA FRACTURA
ISSN 0213-3725
Vol. 28
Año 2011
Págs.39 - 44
En la primera parte de este trabajo se realiza una revisión de los distintos modelos de fallo de la madera en estados de carga multiaxial propuestos hasta el momento. A continuación se hace un análisis estadístico del ajuste de dichos criterios a resultados experimentales, encontrados en la literatura, de ensayos realizados en madera de abeto blanco bajo distintas condiciones de carga. Finalmente se propone un nuevo criterio de fallo no continuo con el cual, sin aumentar el número de parámetros requeridos por otros criterios, se obtiene un mejor ajuste a los datos experimentales.
Revista:
REVISTA INTERNACIONAL CONSTRULINK
ISSN 1645-5576
Vol. 9
N° 28
Año 2011
Págs.39 - 44
Revista:
MAS MADERA
ISSN 0213-3741
N° 5
Año 2011
Págs.32 - 35
Revista:
Composite Structures
ISSN 0263-8223
Vol. 92
N° 12
Año 2010
Págs.2955 - 2965
As a natural resource, an efficient use of wood should be also a requirement for structural timber design, but the usual structural solid sections do not achieve the required optimal behaviour. The performance of the structural elements (serviceability and strength) depends not only on the material properties, but mainly on the moment of inertia of the cross section. The Timber Construction Institute of Technische Universität Dresden has developed a process for the manufacture of structural wood profiles. The resulting profiles combine economy, an efficient use of the material and optimal structural performance. They are externally reinforced with composite fibres, which improve the mechanical characteristics of the wood and protect it from weathering. The available experimental tests to axial loading show the outstanding properties of this new technology. Herein, the preliminary model developed to obtain the axial strength of longitudinally compressed tubes is presented. Two different analytical algorithms are discussed and applied. The model adequately predicts the axial strength of fibre reinforced wood profiles. The analytical results are within an error less than 10% to the available experimental results, with a mean error ratio less than 3%.